Inlet air filter is blocked

Specific reasons: the rubber pipe is bent and blocked by air, and the foam plastics in the air filter is blocked by dust, which is seriously rich in oil caused by the blockage of air intake.

Repair: Trim the intake pipe and clean the foam from the empty filter. If the air filtration is normal, adjust the carburetor so that it is not seriously rich

The carburetor is not properly adjusted

Specific reason: the main oil content hole is blocked by impurities caused by high speed oil. High speed oil enrichment caused by dust blockage of main oil distribution orifice. The carburetor choke is still in the cold start position. The carburetor main oil needle is out of position. Carburetor diameter is too small. High speed rich oil blocked by empty filter.

If the carburetor's air adjustment screw is not adjusted properly, the main injection needle is too low, or the float chamber oil level is too low, resulting in too thin mixture, the carburetor will be shut down and temper.

Exhaust pipe is blocked

Specific reasons: the exhaust pipe is blocked by carbon ash, and the bending part of exhaust front section is dented; These cars have no problem moving at low speed, but not at high speed.

Repair method: remove the exhaust pipe, clean the spring with sewer or hand electric drill clamp wire rope scraping the internal carbon, filling high quality gasoline. The impure substances in gasoline such as wax and gelatine are the main components of carbon deposition, so the tendency of carbon deposition in gasoline with high cleanliness is weak.

Camshaft installation dislocation or alignment disorder

Specific reason: timing small chain installation dislocation, resulting in exhaust time too late. Camshaft alignment disorder, resulting in poor intake and exhaust timing.

Repair: If the installation is confirmed to be a misalignment, reinstall the camshaft. If camshaft alignment is off, polish or repurchase.

The exhaust channel of the four stroke cylinder head is seriously carbonized

Specific reason: Carburetor long-term serious rich oil. The ignition Angle of the igniter is not correct for a long time. Long-term use of non-standard fuel. The engine burns oil.

Repair: remove the cylinder head, with a small flat driver shovel clean cylinder head exhaust channel inside the carbon layer; And adjust the carburetor. Either switch to a plunger carburetor or adjust the carburetor to a depleted oil state and slowly burn off the carbon deposits.

The exhaust passage of the two punch cylinder is seriously carbonized

Specific reason: Carburetor long-term serious rich oil. The ignition Angle of the igniter is not correct for a long time. Long-term use of non-standard fuel. Use a mixture of oils.

Repair: If confirmed, remove the cylinder head, move the piston to the bottom dead center, and use a small flat driver to remove carbon in the cylinder head exhaust channel. Or use a plunger carburetor. Adjust the carburetor to lean oil. Reduce the use of lubricants. Clean up regularly.

The igniter does not give an early ignition Angle

Specific reason: ignition advance Angle is too small. The original model was made of 70 # gasoline, and the new flywheel has a different trigger boss. I had encountered such a flywheel, but I did not expect it at that time. There was also abnormal damage to the firearm, turning it into a fire along the rear of the triggering platform.

Fix: If you can't find the original flywheel, modify the trigger boss by yourself, or make your own "dislocation key" to trigger the boss. The flywheel should find the upper dead point of the piston, and then measure the position between the trigger boss and the igniter sensor. It should be 26 ~ 30 degrees. It is difficult to check the trigger boss for some two - punch or four - punch girder cars. It can be seen from the performance of the engine at each speed stage.

Slight engine wear

Specific reason: the size of the friction velocity

Repair method: in the cold car start, can be in front of the first gear, pinched clutch trolley on 30-40 meters, and then hang the neutral gear, release the clutch, turn on the switch, close the choke, after the normal start car, so as to reduce engine wear.