1, motorcycle crash car wipe flower how to do?

Often driving, bumps and bruises are very normal, fall or driving force is improper, may cause motorcycle lamp shade, protection plate and other plastic scratches, metal parts break, thread slide is a common phenomenon, these situations, the best solution is to use 103 high-strength fast two-in-one glue can be quickly repaired, saving money and effort.

1. When repairing thread sliding wire operation, first clean and clean the aluminum chips and mud in the sliding wire hole, and then evenly apply 103 glue to the inner wall of the hole, and fix the cylinder head stud family manhole for 2 hours, you can use it normally.

2, motorcycle protection board, lampshade and other plastic parts damaged, according to the instructions to use 103 glue treatment is more convenient and practical. However, damage to important parts cannot be repaired in this way, and new parts must be replaced.

2, motorcycle paint fade how to do?

There are many reasons for the motorcycle surface paint fading, such as purification materials in the atmosphere, oil fumes, chemical gases, etc., paint fading and paint oxidation are still somewhat different, if the main color will make the paint show different levels of color difference, the same as the usual paint fading and polishing can be handled. Remember: Frequent car washing can also ease the fading of the paint!

3, how to eliminate the crack of motorcycle shell?

The possibility of causing the shell to crack is that the motorcycle sprayed with metal paint and the car newly sprayed with paint, the paint of the car will show some unusually thin cracks. The beginning is a small piece at first seep into a large, if the Lord is not properly incurred! Waxing can prevent this sign.

4， why will the car paint oxidize? How to deal with it?

Very simple truth, the car paint in the ultraviolet light, for a long time, the paint will show a dark color, the color becomes lighter environment. When encountering the result of paint oxidation, as long as the coating or plating crystal stops covering the paint through the process of scheduled coating, it can not only reduce oxidation but also prevent small scratches.

5, how to remove the old decals stuck on the motorcycle?

On the spur of the moment, some stickers on the motorcycle body, after the wind and spring rain, after the sun burst, some body decals often become old and hairy, but you are difficult to uncover it, how to do?

A good way to share: first, soak the decal in water for about 301min, make it wet, and then dip a drawing eraser in a little detergent solution, rub on the decal, after a while, the decal and some dirt are rubbed into strips and fall down. Then rinse the surface of the car with water.

6, how to deal with rust of motorcycle fuel tank?

As we all know, rust in the tank of the motorcycle is often encountered, and if it is not removed in time, it may block the oil circuit, but it is very troublesome to clean up. You can find a small stick about 30 centimeters long and slightly flexible, fix a magnet at one end and stretch it into the bottom of the tank, and then take it out to clean up the rust on the magnet. This can be done several times to remove the rust.

The exhaust pipe is also a frequently rusted area, and the treatment method is the same as the rust removal of the tank above.

7, how to clean the motorcycle carburetor?

In the use of motorcycle carburetor, there is often sediment and water at the bottom of the carburetor, which affects the normal running of the vehicle. The following describes a method that can be cleaned without removing the carburetor: First turn off the oil switch, loosen the oil screw at the bottom of the carburetor with a screwdriver, and then open the oil switch, until there is oil flow out of the throttle outside the wall of the waste oil pipe to keep blowing (or pump).

At this point, it will be found that mud and water are sprayed from the bottom of the carburetor drain line. Repeat this several times to clean the sediment and water in the carburetor buoy. Then tighten the bottom screw and the motorcycle can be used normally.

8, motorcycle chain rust how to refurbish?

Many people often change the chain with serious wear, in fact, the chain is only worn in one direction. A chain has four directions that can be changed completely, as long as you open the chain latch, turn the chain over and reinstall it, as good as a new chain.

When the two sides of the inner ring are worn, the chain can be disassembled and turned over to make the inner ring into the outer ring, so that two new faces can continue to be used. When all four sides of the chain are completely worn, it is not too late to replace them.

In either case, take some time to wipe the back sprocket clean, spray some cleaning agent on the rag to wipe, if it is dirty, it needs to be poured over it, and then carefully brush the brush and let the chain run through the brush. After cleaning, it's time to lubricate, be sure to make it clear that we need to lubricate this part, both sides of the chain, the side gasket and the overlapping part of the chain, turn the wheel with your right hand, first lubricate the inside of the chain.

9. How to clean and refurbish some non-metal parts?

Motorcycle parts are suitable for various, there are metal parts, there are non-metal parts, and we often encounter some non-metal parts need to be cleaned. These parts cannot be cleaned with kerosene, diesel, gasoline and metal cleaning agents used to clean metal parts, otherwise, it will cause deterioration and failure, and the cleaning method should be determined according to the material of the parts:

1. Rubber parts should be cleaned with alcohol.

2. Parts made of foam should be cleaned with detergent or soapy water.

3, leather parts should not be washed with any cleaning solution, and can be wiped with cloth.

4, paper parts can not be cleaned with water, the application of brush brush, or in kerosene, diesel cleaning.

5, the clutch friction plate, brake shoe friction plate can not be cleaned with kerosene, diesel, alkali solution, the application of gasoline scrub.

10, motorcycle surface electroplating parts how to remove rust?

The appearance affects the vision, and the electroplated parts on the motorcycle will have different degrees of rust due to wear or erosion by rain, serious rust, both affecting the appearance and damage parts, can be removed by a non-corrosive coating rust method.

First put ammonium acetate (white powder crystal, chemical store sale) into the same amount of water, to be fully dissolved after the temperature to about 70 ° C, with a soft cloth dipped in the solution to scrub the rust part, until the rust disappears, and then wipe the residual solution with a dry cloth, the plating part is bright as before.

11. How to maintain electroplating parts?

Electroplating Most corrosive solutions are stable in organic acids and can maintain luster for a long time. However, the following situations will cause the plating to be corroded, and it is necessary to pay attention and take measures to protect it.

1, for the wipe of plastic electroplating parts, can only use a soft cloth dipped in water (warm water) wipe, can not be dipped in oil wipe, because it will destroy the coating of plastic electroplating parts.

2, for the exhaust pipe, fender, rim such plating parts, can not use wire brush dirt, because the wire brush brush will scratch the coating surface. Use clean water to loosen the dirt and dirt and then wipe it according to the above method. If the bubble is really not loose, use a wooden rod to gently descaling.

3, should prevent contact with salt, hydrochloric acid, bittern and other substances. Because the coating is easily soluble in the above substances, it is necessary to avoid contact with 84 disinfectant, bleaching powder, toilet cleaning and other substances.

4, motorcycles should not be stored in a place with gas, briquette stove, and coal smoke. This is because carbon monoxide (CO) will cause the coating to produce gray-black network cracks and rust.

5, for the galvanized surface on the strip, due to its surface generated a layer of dark gray basic zinc carbonate film, can effectively prevent the internal metal from being corroded, so pay attention to do not have to wipe this layer of dark gray galvanized surface clean, polish, you can wipe some neutral oil to protect.

6, pay attention to the method of wiping. Usually in a week only need to wipe the motorcycle electroplating once neutral oil, such as sewing machine oil. Note that the dirt should be wiped with a soft cloth each time the oil is rubbed; After driving in rainy days, clean the dirt with clean water first; Then wipe with a soft cloth, and finally wipe with oil. Do not touch the oil on the paint and tire when rubbing, to prevent paint loss and tire aging. If there is water mist inside the meter and other coatings, it should be dried with a hair dryer and then wiped.